上海地区大气中氯化氢和颗粒氯排放源清单初步研究

氯自由基对于臭氧和二次气溶胶的生成贡献不容忽视.夜间颗粒相氯(Cl~-)可以通过与N_2O_5的复杂反应转化生成ClNO_2,其光解产生的氯自由基将显著影响大气污染的形成机制.本文以上海地区为案例,以2017年为基准年,收集了人为源活动水平数据,采用排放系数估算方法,首次建立了上海地区人为源氯化氢(HCl)和颗粒氯(Cl~-)的排放清单;并进一步结合模型计算海盐气溶胶排放的颗粒氯(Cl~-).结果表明,2017年上海市人为源和天然源排放的HCl和Cl~-分别为1207 t和820 t,其中,燃煤、工业、垃圾焚烧和秸秆燃烧产生的HCl排放量分别为327、134、722和24 t.燃煤源中的燃煤电厂和其它行业燃烧约占燃煤源排放的80%;工业源中水泥为HCl的最大排放源,约占工业源排放的51%;垃圾焚烧厂排放约占总HCl排放的60%,为最大的HCl排放源.燃煤、工业源、垃圾焚烧、秸秆焚烧、烹饪源和海盐的颗粒Cl~-排放量分别为82、153、498、47、39和0.6 t,燃煤源中的燃煤电厂占燃煤Cl~-排放的40%,供热、其他行业和家庭燃烧分别占燃煤Cl~-排放的24%、22%和14%;钢铁行业为工业源的主要Cl~-排放源,约占工业源排放的90%,垃圾焚烧厂占全部Cl~-排放的61%,烹饪源中餐饮企业为最主要排放源,占烹饪源的70%;天然源海盐的排放量极少,未占到总排放的1%.从空间分布来看,浦东新区、宝山、普陀、松江和金山排放的HCl和Cl~-占到全市人为源总排放的80%,为主要的HCl和Cl~-排放区域.本文研究建立的上海地区大气中氯化氢和颗粒氯排放源清单,对于深入研究氯化学机制对二次污染的影响提供了重要的数据参考.     

MnO2/Al2O3催化剂-微气泡臭氧体系催化降解喹啉及其机理

制备了纳米MnO₂,并以Al₂O₃为载体制备了掺杂型MnO₂/Al₂O₃颗粒催化剂.催化剂焙烧温度和时间分别为500℃和4 h、MnO₂质量分数为8%时,催化剂具有最高的臭氧催化氧化活性.SEM分析表明,纳米MnO₂均匀分布于Al₂O₃载体表面.MnO₂/Al₂O₃催化剂的比表面积（BET）为183.22 m²·g^-1,平均孔容为0.27 cm³·g^-1,平均孔径为4.87 nm.建立了MnO₂/Al₂O₃催化剂-微气泡臭氧催化反应体系,研究了该体系对喹啉的降解去除效果及其机理.臭氧微气泡的平均粒径为61.7 μm.微气泡臭氧投量为30 mg·L^-1时,反应60 min后喹啉去除率能达到95%以上;反应20 min后,MnO₂/Al₂O₃催化剂-微气泡臭氧体系对实际煤化工废水二级出水的TOC去除率可达到55%以上.以叔丁醇作为分子探针,证明了羟基自由基（·OH）氧化作用在臭氧微气泡催化氧化体系中对喹啉的降解起到主导作用.     

成都市及周边地区严重臭氧污染过程成因分析

结合天气形势,地面观测资料和WRF-CMAQ模式,分析了2017年7月8~15日成都市一次罕见持续O₃污染过程的特征及成因,量化了各个物理化学过程对此次污染过程的相对贡献,并通过敏感性实验分析了四川盆地内O₃及其前体物的区域传输和本地光化学反应对此次污染过程的影响.结果表明,此次O₃持续污染过程主要是因为四川盆地内盛行偏东风,导致盆地东部城市群的O₃及其前体物经区域输送到成都及周边地区,加之成都市出现小风、气温升高等气象条件进而形成,属于典型的传输性爆发污染.持续污染形成的主要物理化学机制体现为日间气相化学过程贡献为稳定的正值,加之输送过程贡献出现爆发式升高,进而导致近地面O₃小时净增量迅速上升且高达50μg/（m³·h）,随之O₃浓度迅速响应,产生爆发式增长.此外,敏感性实验结果显示此次成都市O₃持续污染的形成受区域输送影响较受本地光化学反应影响更为明显.O₃污染爆发前上游地区高浓度O₃及其前体物沿流场输送并在成都及周边地区不断积累,导致日间O₃浓度不断升高.     

固定源可凝结颗粒物稀释采样器的设计

固定污染源烟气排放进入大气环境后稀释降温,气相中部分饱和蒸气压较低的组分转化为可凝结颗粒物,这部分颗粒物在固定源烟气颗粒物监测中通常被忽略.为评价固定源可凝结颗粒物的排放情况,本文设计开发并评测了一套稀释采样器.稀释采样器稀释比在10：1~40：1范围内,混合停留时间为5~10 s.实验室评测结果表明,稀释气颗粒物背景值低（（~0.1±0.08） 个·cm^-3）,稀释采样器气密性良好,烟气和稀释气能够均匀混合,颗粒物损失较少,细颗粒物 （PM_2.5）损失在5%以下.本稀释采样器能模拟烟气与环境空气混合降温过程,可用于固定源可凝结颗粒物的测量.     

DOC+CDPF对国III重型柴油货车实际道路排放的影响

利用便携式车载排放测试系统（PEMS）对2辆加装氧化催化转化器（DOC）和催化型柴油颗粒捕集器（CDPF）与否的国III重型柴油货车进行实际道路排放测试.结果表明,2辆改造重型柴油车的CO、THC、固态颗粒物粒数（SPN）和黑碳（BC）实际道路排放因子分别为（1.31±0.37）g/（kW×h）、（0.20±0.03） g/（kW×h）、（7.13×10¹⁰±5.27×10¹⁰）个/（kW×h）和（0.69±0.06）mg/（kW×h）,相对于原始排放（拆除DOC+CDPF）分别降低52.48%、55.69%、99.91%和99.22%.从低速、中速到高速,CO和THC减排比例呈现上升趋势,然而运行工况对SPN和BC减排比例则无显著影响.加装DOC+CDPF会导致NO₂在NO_x中的占比升高,且从低速、中速到高速涨幅依次增大,但对NO_x无明显减排效益,其排放因子为9.53~9.83g/（kW×h）,远高于实验室排放限值.     

Preparation of hydrophobic hierarchical pore carbon–silica composite and its adsorption performance toward volatile organic compounds

Carbon–silica materials with hierarchical pores consisting of micropores and mesopores were prepared by introducing nanocarbon microspheres derived from biomass sugar into silica gel channels in a hydrothermal environment.The physicochemical properties of the materials were characterized by nitrogen physical adsorption(BET),scanning electron microscopy(SEM),and thermogravimetric(TG),and the adsorption properties of various organic waste gases were investigated.The results showed that microporous carbon materials were introduced successfully into the silica gel channels,thus showing the high adsorption capacity of activated carbon in high humidity organic waste gas,and the high stability and mechanical strength of the silica gel.The dynamic adsorption behavior confirmed that the carbon–silica material had excellent adsorption capacity for different volatile organic compounds(VOCs).Furthermore,the carbon–silica material exhibited excellent desorption characteristics:adsorbed toluene was completely desorbed at 150℃,thereby showing superior regeneration characteristics.Both features were attributed to the formation of hierarchical pores.     

石墨烯/聚苯胺修饰阴极对反硝化MFC性能影响

反硝化生物阴极微生物燃料电池（MFC）以电极为电子供体,在自养条件下完成硝酸盐去除过程.本研究以碳布（CC）为基底材料,分别制备获得还原氧化石墨烯修饰（rGO-CC）,聚苯胺修饰（PANI-CC）及二者复合修饰的CC电极（rGO/PANI-CC）,并考察其作为阴极材料对反硝化生物阴极MFC产电脱氮性能的影响.扫描电镜结果显示,rGO-CC和PANI-CC的碳纤维分别被片层状rGO和网状PANI覆盖,而rGO/PANI-CC表面呈现PANI在附着rGO的碳纤维上团聚的形貌,均增大了碳布的比表面积.循环伏安测试显示,rGO/PANI-CC具有最高的电化学活性.以rGO-CC,PANI-CC和rGO/PANI-CC为阴极构建MFC的产电能力分别提高了82%,24%和41%,其阴极对NO₃^--N的去除能力增强了23%,9%和13%.16S rDNA测序结果揭示修饰后电极表面微生物的多样性下降,Stappia和Pacacoccus属微生物的丰度增加.     

Performance of different macrophytes in the decontamination of and electricity generation from swine wastewater via an integrated constructed wetland-microbial fuel cell process

Plants constitute a major element of constructed wetlands(CWs).In this study,a coupled system comprising an integrated vertical flow CW(IVCW) and a microbial fuel cell(MFC) for swine wastewater tre atment was developed to research the effects of macrophytes commonly employed in CWs,Canna indica,Acorus calamus,and Ipomoea aquatica,on decontamination and electricity production in the system.Because of the different root types and amounts of oxygen released by the roots,the rates of chemical oxygen demand(COD) and ammonium nitrogen(NH_4~+-N) removal from the swine wastewater differed as well.In the unplanted,Canna indica,Acorus calamus,and Ipomoea aquatica systems,the COD removal rates were 80.20%,88.07%,84.70%,and 82.20%,respectively,and the NH_4~+-N removal rates were 49.96%,75.02%,70.25%,and 68.47%,respectively.The decontamination capability of the Canna indica system was better than those of the other systems.The average output voltages were 520±42,715±20,660±27,and 752±26 mV for the unplanted,Canna indica,Acorus calamus,and Ipomoea aquatica systems,respectively,and the maximum power densities were 0.2230,0.4136,0.3614,and0.4964 W/m~3,respectively.Ipomoea aquatica had the largest effect on bioelectricity generation promotion.In addition,electrochemically active bacteria,Geobacter and Desulfuromonas,were detected in the anodic biofilm by high-throughput sequencing analysis,and Comamonas(Proteobacteria),which is widely found in MFCs,was also detected in the anodic biofilm.These results confirmed the important role of plants in IVCW-MFCs.     

Revealing the changes of bacterial community from water source to consumers tap: A full-scale investigation in eastern city of China

This study profiled the bacterial community variations of water from four water treatment systems, including coagulation, sedimentation, sand filtration, ozonation-biological activated carbon filtration (O₃-BAC), disinfection, and the tap water after the distribution process in eastern China. The results showed that different water treatment processes affected the bacterial community structure in different ways. The traditional treatment processes, including coagulation, sedimentation and sand filtration, reduced the total bacterial count, while they had little effect on the bacterial community structure in the treated water (before disinfection). Compared to the traditional treatment process, O₃-BAC reduced the relative abundance of Sphingomonas in the finished water. In addition, ozonation may play a role in reducing the relative abundance of Mycobacterium. NaClO and ClO₂ had different effects on the bacterial community in the finished water. The relative abundance of some bacteria (e.g. Flavobacterium, Phreatobacter and Porphyrobacter) increased in the finished water after ClO₂ disinfection. The relative abundance of Mycobacterium and Legionella, which have been widely reported as waterborne opportunistic pathogens, increased after NaClO disinfection. In addition, some microorganisms proliferated and grew in the distribution system, which could lead to turbidity increases in the tap water. Compared to those in the finished water, the relative abundance of Sphingomonas, Hyphomicrobium, Phreatobacter, Rheinheimera, Pseudomonas and Acinetobacter increased in the tap water disinfected with NaClO, while the relative abundance of Mycobacterium increased in the tap water disinfected with ClO₂. Overall, this study provided the detailed variation in the bacterial community in the drinking water system.